Huba Pressure sensor for shipbuilding 527

The compact type 527 pressure transmitter is based upon the well proven ceramic technology developed by Huba Control over 20 years ago.
These pressure transmitters are suitable for applications across a broad spectrum of industries and shipbuilding.

Compact, rugged construction
Negligible temperature influence on accuracy
Certified  for shipbuilding with:
 - Germanischer Lloyd
 - American Bureau of Shipping
 - Bureau Veritas
 - Det Norske Veritas
 - Lloyd`s Register

Pressure range
Relative     0 ă 60 bar
Absolute     0 ... 1 ă 16 bar
Operating conditions
Medium      Liquids and gases
Temperature
      
Medium
FPM -15 ... +125 ÀC
     EPDM -40 ... +125 ÀC
     NBR -20 ... +100 ÀC
    Ambient   -30 ...   +85 ÀC
    Storage   -50 ... +100 ÀC
Tolerable overload / Rupture pressure
   < 4 bar 3.0 x fs
    > 4 bar 2.5 x fs
Materials
Cover     Stainless steel 1.4404 / AISI 316L
Plug accommodation    Polyarylamide 50% GF V0
Materials in contact with medium
   Pressure connection Stainless steel 1.4404 / AISI 316L
    Sensor Ceramic Al2O3 (96%)
    Sealing material FPM, EPDM, NBR
Electrical overview
  Output Power supply Load Current consumption
2 wire  4 ... 20 mA   7 ... 33 VDC <
supply voltage - 7 V
 [Ohm] < 23 mA
2 wire (Ex)  4 ... 20 mA 10 ... 30 VDC <
supply voltage - 10 V
 [Ohm] < 23 mA
3 wire  0 ... 10 V 12 ... 33 VDC >10 kOhm / < 100 nF <   7 mA
Polarity reversal protection            Short circuit proof and protected against polarity reversal. Each connection is protected against crossover up to max. supply voltage.
Protection class
Protection class III
Dynamic response    
Response time     < 2 ms, 1 ms typ.
Load cycle     < 100 Hz
Protection standard      
Connector DIN EN 175301-803-A    IP 65
Swift connector, Connector M12x1    IP 67
Electrical connection
Swift connector with cable 1.5 m (PVC spec.)  
Connector DIN EN 175301-803-A       
Connector M12x1
Pressure connection
Inside thread
  
7
/16 - 20 UNF  
    ½ - 14 NPT 
Outside thread
7
/16 - 20 UNF      
    ¼ -18 NPT      
  G ¼  sealed at back DIN 3852 form E with Profile seal ring in FPM spec. (-30 ... +135 ÀC)
  G ½ sealed at back and manometer (combi) with Profile seal ring in FPM spec. (-30 ... +135 ÀC)
  M20x1.5
  G ½ sealed at front
Installation arrangement
Unrestricted
Tests / Admissions
Electromagnetic compatibility CE conformity acc. EN 61326-2-3
Shock acc. IEC IEC 68-2-27 100 g, 11 ms half sine wave, all 6 directions, free fall from 1 m on concrete (6x)
Constant shock acc. IEC 68-2-29  40 g for 6 ms, 1000x all 3 directions
Vibration acc. IEC 68-2-6 20 g, 15 ... 2000 Hz, 15 ... 25 Hz with amplitude μ 15 mm, 1 Octave/min. all 3 directions, 50 constant load
Shipbuilding
  Germanischer Lloyd
  American Bureau of Shipping
  Bureau Veritas     
  Det Norske Veritas     
  Lloyd`s Register    
Protection against explosion
Intrinsic safety ÿiŸ (with current output only)
   Ex II 1/2 G Ex ia IIC T4 Ga/Gb
     Ex II 1/2 D Ex ia IIC T125ÀC Da/Db
EC type examination certificate    SEV 10 ATEX 0145
Connection to certified intrinsically safe resistive circuits with maximum values  Ui = 30 VDC; Ii = 100 mA = Pi = 0.75 W
Effective internal inductance and capacitance for versions with plugs complying with EN 175301-803 or M12x1 Li = 0 nH; Ci = 0 nF
Weight
~ 90 g

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below: