SMC solenoid valve 4 & 5 Port SV

The SV series employs a multi-connector instead of the conventional lead wires for internal manifold wiring. By connecting each block with a connector, changes to manifold stations are greatly simplified. Cassette base type manifolds offer the ultimate in flexibility. Manifold sections can be added using a simple release mechanism. Conventional tie-rod base type manifolds are also available. The use of 34 pin connectors allows up to 16 stations with double solenoids. Single valve, sub-plate type IP67 protection Fluid: air Port sizes: 1/8, 1/4, 3/8, 1/2 Thread types: Rc, G, NPT, NPTF Clean room series  

The SV series employs a multi-connector instead of the conventional lead wires for internal manifold wiring. By connecting each block with a connector, changes to manifold stations are greatly simplified. Cassette base type manifolds offer the ultimate in flexibility. Manifold sections can be added using a simple release mechanism. Conventional tie-rod base type manifolds are also available. The use of 34 pin connectors allows up to 16 stations with double solenoids. Fluid: air Operating pressure range: -100kPa to 0.7MPa Response time ms (at 0.5MPa): 18 or less Coil rated voltage: 12, 24VDC Ambient & fluid temperature: -10 to 50° C Enclosure: IP67 (based on IEC529)  

The SV series employs a multi-connector instead of the conventional lead wires for internal manifold wiring. By connecting each block with a connector, changes to manifold stations are greatly simplified. Cassette base type manifolds offer the ultimate in flexibility. Manifold sections can be added using a simple release mechanism. Conventional tie-rod base type manifolds are also available. The use of 34 pin connectors allows up to 16 stations with double solenoids. Single valve, sub-plate type IP67 protection Fluid: air Port sizes: 1/8, 1/4, 3/8, 1/2 Thread types: Rc, G, NPT, NPTF  

Supply / Exhaust port block disk for Series SV Type 10: Tie-Rod Base Manifold. By placing a SUP block disk in a manifold valve's pressure supply passage, two different high and low pressures can be supplied to one manifold. By installing an EXH block disk in a manifold valve's exhaust passage, the valve's exhaust can be separated so that it will not affect other valves. It can also be used on a manifold with mixed positive pressure and vacuum. (Two pieces are required to block EXH on both sides. However, Series SV1000 and 2000 type 10 manifolds require only one piece.) Supply / Exhaust port block disk for Series SV Type 10: Tie-Rod Base Manifold  

Blanking plate for covering empty stations on series SV valve manifolds where valves will be added in the future, or for maintenance. For covering empty stations on series SV valve manifolds for future expansion or maintenance Includes mounting screws  

Clamp Assembly for DIN rail mounting Series SV Type 10: Tie-Rod Base Manifold. For Series SV Type 10: Tie-Rod Base Manifold DIN rail mounting  

Replacement gasket for where the valve solenoid connects to manifold block assembly. Replacement gasket for where valve solenoid connects to manifold block assembly.  

The SV series employs a multi-connector instead of the conventional lead wires for internal manifold wiring. By connecting each block with a connector, changes to manifold stations are greatly simplified. Cassette base type manifolds offer the ultimate in flexibility. Manifold sections can be added using a simple release mechanism. Conventional tie-rod base type manifolds are also available. The use of 34 pin connectors allows up to 16 stations with double solenoids. Fluid: air Operating pressure range: -100kPa to 0.7MPa Response time ms (at 0.5MPa): 33 or less Coil rated voltage: 12, 24VDC Ambient & fluid temperature: -10 to 50° C Enclosure: IP67 (based on IEC529)  

Various roundhead combination mounting screws for series SV2000, SV4000 valve manifolds. Various mounting screws for SV2000, SV4000 For valve mounting, spacer assembly, interface regulator  

The SV series employs a multi-connector instead of the conventional lead wires for internal manifold wiring. By connecting each block with a connector, changes to manifold stations are greatly simplified. Cassette base type manifolds offer the ultimate in flexibility. Manifold sections can be added using a simple release mechanism. Conventional tie-rod base type manifolds are also available. The use of 34 pin connectors allows up to 16 stations with double solenoids. SV3000 series valve Single, double solenoid & 3 position available Service life: 50 million cycles or more Supply pressure: 0.5MPa Unrestricted mounting orientation  

The SV series employs a multi-connector instead of the conventional lead wires for internal manifold wiring. By connecting each block with a connector, changes to manifold stations are greatly simplified. Cassette base type manifolds offer the ultimate in flexibility. Manifold sections can be added using a simple release mechanism. Conventional tie-rod base type manifolds are also available. The use of 34 pin connectors allows up to 16 stations with double solenoids. SV4000 series valve Single, double solenoid & 3 position available Service life: 50 million cycles or more Supply pressure: 0.5MPa Unrestricted mounting orientation  

The SV series employs a multi-connector instead of the conventional lead wires for internal manifold wiring. By connecting each block with a connector, changes to manifold stations are greatly simplified. Cassette base type manifolds offer the ultimate in flexibility. Manifold sections can be added using a simple release mechanism. Conventional tie-rod base type manifolds are also available. The use of 34 pin connectors allows up to 16 stations with double solenoids. Single valve, sub-plate type IP67 protection Fluid: air Port sizes: 1/8, 1/4, 3/8, 1/2 Thread types: Rc, G, NPT, NPTF